![]() ![]() If done correctly your case should now look like this.Īs you can see above the holes are not damaged in any way and can have replacement rivets put in to hold the sides of the bay once again if you wish.Īs you can see above the sides of the HDD bay are not damage what so ever. Now that you have removed these rivets you repeat these steps for the rivets holding the HDD cage sides to the CD/DVD drive cage but and remove those rivets. As you see below I currently have two rivets completely removed and the tool I used to do it. Now once you have removed all the rivet heads you will need a hammer and the "hole puncher" to remove the rest of the rivet. The other three still have some work left in them. The rivet in the bottom left corner has already lost its head and is ready for removal. In the picture above you can see that the rivets on the bottom of my case are already being drilling into. You have to apply some force to the power drill to get the rivet head to start spinning but if you happen to run into a fully spinning rivet where the entire rivet is spinning, just grab a pair of needle noise pliers and grab the other end, hold it firmly, then continue to drill until the rivet head pops off. If you do this correctly you will not break the case nor ruin the holes where the rivets were. You want to drill directly in the hole this way once you get to a certain point the top of the rivet, the part you see above, will then start to spin and break off. Ok so now that you have everything ready to go what you want to do now is take a power drill with a small drill bit and start to drill into the rivet. Since this was not much work to do I did it in my garage. Ok now that we have removed EVERYTHING completely from this case it is time to throw on your protective eye wear and move to your work area. I also removed this with the same method. I also have a little speaker for the motherboard. Push in the sides to unlock the clips and slide out. This to latched onto the case itself so you had to use the same method as above to remove it. Now this next picture is to show you the Power/Reset button. It also shows how and where you want to press in to release the lock to remove these ports. This is a side shot of the USB/Audio Port to show that the clips were not broken when removed. On this case they simply just locked in so I had to press the sides with a flat head screw driver to remove them with out damaging the casings or the latches used to latch onto the case. So before moving on you want to remove these. This particular case did not have the USB/Audio connections and the Power/Reset button on the actual panel face as I will show below.Īs you can see my power/reset button and cables as well as my USB/Audio ports are connected to the actual chasis and not the front panel. You will next want to remove the front panel face. Obviously you need to remove any and all components such as your PSU, Motherboard, Case Fans, Liquid Cooling, CD/DVD Drives, Hard Drives, Video Card(S), Sound Card, and any other components not listed. The rivets connecting it to the DVD/CD Drive bay were painted so those wont be visible.īefore moving on there are some things you need to remove. I took it at an angle so you can see the bottom rivets on my case. So here are some before pictures before I removed the rivets. The reason for doing this is to free up room in this case for future modding. ![]() ![]() The part I will be removing is the side rails where you mount your hard drives and floppy disks. Tools you will need A Power Drill, Small drill bit that will fit in the hole part of the rivet, a pair of players to hold the rivet while drilling if it starts to turn on its own, a hammer, protective eye wear, and I am not sure the exact name of it but a screw driver that has a needle like head (the hole puncher) Removing the HDD Drive Bays that are connected to my case with rivets. The way I removed them allows me to re-use the holes and replace the rivets with new rivets. Below are the steps I took if anyone else is trying to remove rivets safely. They were connected to the case with rivets so I had to do some modding. View the informational chart below for additional specifications.Ĭheck out our inventory to find the right bifurcated rivets for your application, request a quote, or contact us to learn more.I am not sure if there is already a how to guide on here for this but I was trying to figure out how to remove the rivets from my case so I would be able to totally remove my HDD Drive cages/bays. Different head styles are available, including oval head and truss head split rivets. Jay-Cee Sales & Rivet offers a large, in-stock inventory of standard split rivets.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |